Kuo Lab Wiki

User Tools

Site Tools

You are here: start » computers » server_basic_setup
computers:server_basic_setup

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
computers:server_basic_setup [2018/12/18 00:02] – chkuocomputers:server_basic_setup [2023/10/27 16:54] (current) – hychang
Line 3: Line 3:
 ===== RAID ===== ===== RAID =====
   * high-reliability servers (firewall, DHCP, web, etc)   * high-reliability servers (firewall, DHCP, web, etc)
-    * 4 drives: RAID 1 (* 2), hot spare * 1, cold spare *1+    * 4 drives: RAID 1 (* 2), hot spare * 1, cold spare * 1
   * computational servers   * computational servers
     * RAID 10, hot spare * 1 or 2     * RAID 10, hot spare * 1 or 2
  
 ===== Operating System ===== ===== Operating System =====
-  * [[http://www.ubuntu.com/|Ubuntu]] 18.04 LTS 64-bit Server Edition.+  * [[http://www.ubuntu.com/|Ubuntu]] 20.04 LTS 64-bit Server Edition.
  
 ===== Packages ===== ===== Packages =====
Line 20: Line 20:
 # Zero Configuration Networking (Zeroconf) # Zero Configuration Networking (Zeroconf)
 $ sudo apt install avahi-daemon $ sudo apt install avahi-daemon
 +# in case the avahi-daemon does not work after reboot, log-in using ip address and restart
 +$ sudo service avahi-daemon restart
 +
  
 # remove all unused packages # remove all unused packages
Line 31: Line 34:
 ===== Network ===== ===== Network =====
   * edit ''/etc/netplan/50-cloud-init.yaml'' to configure the network   * edit ''/etc/netplan/50-cloud-init.yaml'' to configure the network
-  * note: use space; NOT tab+    * use space for indentation, NOT tab. 
 +    * or delete the original *.yaml file generated by the installer, then create a new xxx.yaml in ''/etc/netplan''
   * example: eno1 uses DHCP; eno2 uses a static IP   * example: eno1 uses DHCP; eno2 uses a static IP
 <file> <file>
 network: network:
-    ethernets: +  version: 2 
-        eno1: +  renderer: networkd 
-            addresses: [] +  ethernets: 
-            dhcp4: true +    eno1: 
-        eno2: +      addresses: [] 
-            addresses: [140.109.56.170/24] +      dhcp4: true 
-            gateway4: 140.109.56.254 +    eno2: 
-            nameservers: +      addresses: [140.109.56.170/24] 
-                addresses: [140.109.1.10,8.8.8.8,8.8.4.4] +      gateway4: 140.109.56.254 
-            dhcp4: no +      nameservers: 
-    version: 2+        addresses: [140.109.1.10,8.8.8.8,8.8.4.4] 
 +      dhcp4: no
 </file> </file>
-  * after updating the config file, execute: ''sudo netplan apply'' +  * more examples: [[https://netplan.io/examples/]] 
-  * use ''ifconfig'' to check network info:+  * after updating the config file, execute ''sudo netplan try'' to validate, then ''sudo netplan apply'' to apply 
 +  * to check the network info: ''ip a'' 
 + 
 + 
 +  * note: for Ubuntu 16.04 and earlier versions; edit ''/etc/network/interfaces''
  
  
Line 64: Line 73:
 </code> </code>
  
-===== Service ===== 
-==== sshd_config ==== 
-  * In ''/etc/ssh/sshd_config'', change ''PermitRootLogin without-password'' to ''PermitRootLogin no''. 
-  * Limit ssh connection to ipv4 and disable ipv6: uncomment ''ListenAddress 0.0.0.0'' and comment ''#ListenAddress ::''. This setting allows the server to listen to ipv4 only, so normal connections not denied because clients use ipv6 and are rejected based on the rules in ''/etc/hosts.allow'' and ''/etc/hosts.deny''. 
  
- +===== SSH =====
-===== SSH security =====+
   * see [[computers:ssh_security|SSH security]]   * see [[computers:ssh_security|SSH security]]
   * minimal requirement: ''sudo apt install fail2ban''   * minimal requirement: ''sudo apt install fail2ban''
 +  * ''/etc/ssh/sshd_config''
 +    * ''PermitRootLogin no''.
 +    * Limit ssh connection to ipv4 and disable ipv6
 +      * Uncomment ''ListenAddress 0.0.0.0''
 +      * Comment ''#ListenAddress ::''
 +      * This setting allows the server to listen to ipv4 only, so normal connections not denied because clients use ipv6 and are rejected based on the rules in ''/etc/hosts.allow'' and ''/etc/hosts.deny''.
 +
  
 ===== Message Of The Day (motd) ===== ===== Message Of The Day (motd) =====
Line 79: Line 90:
 $ sudo chmod a-x /etc/update-motd.d/10-help-text  $ sudo chmod a-x /etc/update-motd.d/10-help-text 
 $ sudo chmod a-x /etc/update-motd.d/50-motd-news  $ sudo chmod a-x /etc/update-motd.d/50-motd-news 
-$ sudo chmod a-x /etc/update-motd.d/80-livepatch 
 </code> </code>
  
Line 105: Line 115:
 <code bash> <code bash>
 $ sudo adduser username groupname $ sudo adduser username groupname
 +</code>
 +
 +==== Remove User from Group ====
 +<code bash>
 +$ sudo deluser username groupname
 +</code>
 +
 +==== Change username and home directory====
 +<code bash>
 +$ sudo usermod -l new_username old_username
 +$ sudo usermod -d /home/new_username -m new_username
 </code> </code>
  
Line 122: Line 143:
 $ sudo deluser username $ sudo deluser username
 $ sudo delgroup groupname $ sudo delgroup groupname
 +</code>
 +
 +
 +==== Create scratch directory and storage====
 +Run the shell script make_work_dir, which had written by Dr. Kuo.
 +<code bash>
 +$ sudo /home/chkuo/bin/make_work_dir username
 </code> </code>
  
computers/server_basic_setup.1545062524.txt.gz · Last modified: 2018/12/18 00:02 by chkuo